URGENT !!! HELP NEEDED !!!! FOR A BROTHER 700e innovis II
I cleaned my machine and put everything up
as usual and there, I HAVE A HUGE PROBLEM
!!!
thread in the bobin don't go in the
right direction, the start node is not on
my work but in the machine and therefore
the points do not and it blocks me the
needle after a few points...what did I do
wrong ???
Please look the picture
58368 HI Sissi, I have 2 of these machines. one
just had to go in as I to thought I had the
same problem as you thought it was a
problem with the bobbin, turned out a piece
of plastic along the top thread route had
split,and was catching my top thread which
was stopping the bobbin from running
correctly, although my dealer said an
unususal problem was very easily fixed, he
also reset all my tensions for me. I found
this very frustatating as I have 2 of these
so had them side by side to compare as
well, I was so sure it was a problem with
the bobbin I changed parts with both
machines
and in the end had to give in lol big hugs
Maria xxx
by mooie24 16 Oct 2009
this machine is well known for catching the
upper thread around the movements
inside,when threaded and running it appears
to have a bobbin problem, but mostly its
the upper thread problem, then once you
starting running it you know if you have a
problem try this link...
i found this very helpfull helpful in times
of great need lol :-
http://www.annsultfixit.com/UltFixi.
..
6488 I was just going to say the same as mooie24....if another piece of thread is stuck in the upper compartment, it throws the stitching off also....Many is the times mine has done it....some threads aren't as nice as others and don't slide through easily, but catch on any sliver of machines....
11472 
1317 Hello Sisi,
i'm so sorry to hear that the problems
or not from cleaning your machine,
i hope that your machine is faster repaird
than a month,
brother does have a great after sale
service with warranty,
when my machines where broken i did also
dont have to pay one thing for the
repairings because it was in warranty,
i did have the luck that i only did have to
wait for one week for the machine to get it
repaird,i hope that your machine also wil
be repaird quick and that he is working
good again after the repairing,
i'm sorry that i could not help you,gr
connie
19416 Dear Sissi,
So sorry about your problem; sorry I cannot
help. Best of luck with the repair
problems.
Jacqueline
11233 OK girls, the problem of my machine does
not come from a wrong operation after
cleaning. It will then go back to
after-sale next week ... which means I do
not see him again before a month! I'm
too sad!
The good news is that repairs will be made
under warranty, and the tranport go and
return will be free : I would not be
charged
58368 Coucou Sissi, si ton pb n'est pas réglé, tél au 003261411274 et demande à parler à Mr Stecker. Tu lui expliques et s'il peut te dépanner par tél il le fera même si tu n'as pas acheté la machine chez lui. Si le pb vient du porte canette, fais un essai avec l'autre qui est livré avec la machine. Amicalement,
by sissibrode 09 Oct 2009
merci Françoise. Je vais voir ce que me dit mon revendeur et ensuite j'aviserais. Ma machine n'a été livré qu'avec le porte canette inclus, pas d'autre de secours...
3251 If you took the bobbin case out, it may not have seated itself properly when you put it in again. Do it again, and make sure that it lines up and is supported on all sides by the well that the bobbin case fits into. Then, try a new bobbin and a new needle. If I were there, I could show you what I mean. Good luck!
by sissibrode 08 Oct 2009
I have do that Auntbaba, replace the bobin, the bobin compartment, change the upper thread and the needle, but nothing change....
19728 The thread on the bobbin should be going
anti-clockwise, it comes out the front
towards you and you pull it to the right,
down and around the hook/loop plastic piece
then to the left.
Look closely at the diagram etched into the
machine that you can see in your
pictures.
Hope this helps, hugs n roses, Meganne
44627 OK perhaps can you see better what happened with this pictures....
[2]
58368 sissy, did you put your plate on backwards?..San
by marjialexa 08 Oct 2009
Flat silver thing under the foot. Check, but I don't think you did, it has a little notch that looks like it prevents that. Hugs, Marji
730 19416 took a look at pictures,and wonder just
like you what's wrong. I can only
advise, take the parts you removed out
again. and place them back another time,
change the needle and use another bobbin.
And I hope it works properly again. If not:
I'm afraid you have to let the dealer
take a look at it.
hope your embroidery-problem will be fixed!
hugs4u
51341 when you clean your machine what parts do you clean and remove?
19416 i have taken another look at the pictures did you put the bobbin with the thread down in your machine? it looks like your bobbin is not right in the machine,gr connie
19416 I just checked several times: this is not
the bobbin thread is wrong, it's the
top wire that wraps around the bobbin
compartment ...
the can is in the right direction, it is
impossible to deceive.
I don't understand....
58368 Hello ,i have also a brother 700e innovis
II ,
did you put your bobbin good in the
machine?
have you try to start the machine with
another bobbin,i have got a problem with
the bobbin and i did another bobbin in the
machine and the problem was gone,somethimes
does the machine works not good when the
bobbin is not good,
i hope that their is nothing broken in your
machine,i have got problems with my
machines more than one time and everytime
they have to replace a new piece in the
machine,
when i did have the problems with my
machine it also blocked after just starting
embroidering,
i hope that you can fix your machine and
that it is nothing to serieus,gr connie
19416 Sissi, from what I can see, it looks like you have your bobbin thread is going in the wrong direction. Do you need to flip your bobbin over? Check your machine manual. I can see that you have your bobbin holder in correctly. H&*.
9507 Could you possibly have put the bobbin race (the thing that comes out and holds the bobbin) in backwards? And is your bobbin in the right way? I sure hope somebody with a Brother can help you, this is rather different than a Janome! Good luck, hugs, Marji
22364 482 730 Sylvie, I wished that I could help - but I don't know your machine - so I will wish you luck in fixing it and give you a flower. *4U
89876 here the pictures. on 4 and 5 you can see
that the start node is out of place...
Thanks for your help
[2]
[3]
[4]
[5]
58368
My dealer say : "You sure have a problem with the slipway and syncing your machine."... Don't really know what is it :o(